Where Is Air Cabin Filter 2011 Ford Focus

Ford Focus Motel Air Filter Replacement Guide
How to clean or change the HVAC system's cabin air filter element in a 3rd generation (MK III) 2011-2014 Ford Focus.

2012 Focus Kick Panel
Look Beneath Glove Box
Squeeze & Remove Fastener This automotive maintenance tutorial was specifically written to assist owners of the third generation MK III (2011, 2012, 2013 & 2014) Ford Focus sedan or hatchback in cleaning or replacing the A/C system's cabin air filter chemical element.

Owners of other similar Ford vehicles built upon the "Global C" (C1) meaty car platform such equally the C-Max, Escape, Kuga and Transit Connect may also find these DIY instructions to be useful.

A few compatible replacement motel air filter elements include the following with their role numbers: Ecogard XC36174, Motorcraft FP70, Wix 24419, TYC 800183P, NPN # 118418-01181745, ACDelco CF2291 and Cleenaire CAF6196.

A Torx T-fifteen star chip screwdriver may be needed to access the OEM air filter.

A wet/dry store vacuum may also be useful for cleaning the existing element if it isn't very dirty and yous programme on re-using it.

Cap Removed - Yellow Rivet
Remove Nether Dash Panel
Interior Fuse Panel Location The start two steps are to sit in the front passenger seat of the vehicle and and so locate the nighttime grayness carpeted panel below the glove box in the pes well.

The foot well panel is held in place by two round black plastic friction fasteners that are attached to yellow pop rivets.

Edit - A thoughtful person sent an e-mail to inform me that at that place should take been a Torx T-xv star head screw at the bottom of the filter cover. That screw must have been missing on this 2012 Focus.

If your filter cover has a screw on the bottom, loosen it in the counterclockwise management with a Torx T15 screwdriver.

Squeeze the sides of the black plastic fasteners and slide them straight off the yellow popular rivets.

Remove the dark grey human foot well cover and gear up information technology aside in a prophylactic place. Behind the panel, yous'll run into the passenger compartment interior fuse panel.

Squeeze Together Tabs
Pull Off Filter Encompass
Filter Access Panel Removed At the front left area of the human foot well, just in front of the eye console, you'll run across the rectangular black plastic filter access encompass.

Clasp together the two large blackness plastic tabs near the bottom of the cover to release the clips and pull the access panel away from the blower motor housing. Set the filter cover aside in a condom place.

Border of Former Cabin Filter
Begin Sliding Out Filter Once the filter cover has been removed, you'll run across the white or light grey edge of the sometime filter.

Gently slide the quondam filter directly out of the slot in the blower motor housing.

Bend Flexible Filter Out
Filter Slot - Blower Housing
OEM Filter After 30K Miles

You may need to bend the filter to get it around the various tubes, wires, hoses and other plastic panels that are in the way.

Don't be afraid to curve the filter since information technology is flexible and won't be easily damaged. Just be sure to carefully route the filter around the obstructions and don't cause any rips or tears if y'all plan on re-using it.

If the old filter is relatively clean, just tap out whatsoever large droppings and remove the fine grit with a wet/dry vacuum cleaner.

If the old element is dark grey or blackness and clogged with dirt, dust, hair, insects, leaves, pollen and twigs, it should be replaced with a brand new unit. If y'all have astringent allergies, consider purchasing an activated carbon filter.

I recommend ownership the Ecogard XC36174 cabin air filter since it has excellent reviews on Amazon.

Clean Filter With Vacuum
Gently Insert New Filter
Slide Filter In By Fuses Gently insert the new air filter in to the slot with the "Air Flow" indicator arrow facing towards the rear of the vehicle.

Yous will need to compress the pleats or bend the filter to go information technology around the fuse panel and under the bottom of the nuance board. Practise non apply excessive force to avoid violent or puncturing the filter.

New Filter Installed In Slot
Filter Cover & ii Clips
Insert Top Part In First Brand sure that the new filter is fully seated inside the slot with the "Air Flow" pointer facing towards the back of the vehicle.

Insert the summit edge of the rectangular black plastic filter comprehend in place first.

Press Tabs & Push In
Push Lower Finish In Place Pinch together the ii tabs at the end of the springy blackness plastic arms and push the lower part of the comprehend in place.

If your cabin air filter access console was equipped with a screw at the bottom of the encompass, tighten information technology in the clockwise direction with the Torx T15 star bit screwdriver. (The screw was missing on this 2012 Focus sedan.)

Double check that the filter comprehend is securely in identify before moving on to the next steps.

Filter Cover Replaced
Line Upwards Foot Well Embrace Line up the pes well panel and insert the two yellow pop rivets attached to the bottom of the dashboard through the corresponding holes.
Button Black Fasteners On
Slide Black Cap On Yellow Peg
Motel Air Filter Replaced Push the 2 black plastic friction fasteners directly on to the yellow pop rivets to secure the foot well embrace in place.

Relish the fresh clean air from your A/C system!